Search found 68 matches

by JLM
Mon Dec 18, 2023 12:46 pm
Forum: General Discussion - Windmill
Topic: Vane
Replies: 14
Views: 1173

Re: Vane

They must have sold every brand at one time or the other elgin is not very common around here at all. I do know that later on Samsco sold many of the model 24 star mills in the area as well as Fairbury. The 14' 7AA my grandfather installed in the 50's here at my house was sold through them.
by JLM
Sun Dec 17, 2023 9:30 am
Forum: General Discussion - Windmill
Topic: Vane
Replies: 14
Views: 1173

Re: Vane

I was visiting with Jim Collums earlier this year. And we spoke breifly about that old book that was published by F.F. Collins Company in San Antonio. The F.F Collins Company was a dealer for both Eclipse and Star windmills. Apparently Krueger Machinery later on Samsco bought out F.F. Collins Compan...
by JLM
Fri Jul 28, 2023 7:12 pm
Forum: General Discussion - Windmill
Topic: Lordsburg, NM
Replies: 10
Views: 590

Re: Lordsburg, NM

I bet pulling the well under that mill was quite a chore probably took many mules tied together to pull the pipe and rods. Makes me really appreciate the modern water well cranes we have today.Ive got some pictures in a old samson catalog showing two of those mills pumping into a earthen tank in San...
by JLM
Fri Jul 07, 2023 5:01 pm
Forum: General Discussion - Windmill
Topic: Samson steel
Replies: 20
Views: 838

Re: Samson steel

The Boerne area had a handful of big Samsons. One ranch we worked on west of Boerne had the tailbone and vane sheet for an 18' Samson at a well. I'm not sure if the big samson next to the Walmart is still there or its been moved but that was at least a16' mill.
by JLM
Sun Jan 03, 2021 11:46 am
Forum: Wanted
Topic: Somebody look thru...
Replies: 2
Views: 1325

Re: Somebody look thru...

I will see what I have in the yard. Ive been out of touch with the forum the drought in south west texas has been keeping me busy working on wells.
by JLM
Mon Feb 10, 2020 9:34 pm
Forum: General Discussion
Topic: Forum Maintenance - Feb. 9, 2020
Replies: 6
Views: 2444

Re: Forum Maintenance - Feb. 9, 2020

Thank you for keeping everything running smoothly.
by JLM
Mon Jan 27, 2020 6:26 pm
Forum: Wanted
Topic: Mast pipe base for B602/702 Aermotor
Replies: 8
Views: 3577

Re: Mast pipe base for B602/702 Aermotor

If you need a lower furl finger pincher for a three leg stub i have some
by JLM
Sat Jan 25, 2020 4:02 pm
Forum: Technical Discussions - Windmill
Topic: Rods for welding cast iron
Replies: 23
Views: 8584

Re: Rods for welding cast iron

Windys tailpin trick is what we always did that way you didn't have to grind so much and you can gauge it at the same time.You can also cut up the old tailpin to fill in the holes.
by JLM
Thu Jan 23, 2020 12:34 pm
Forum: Projects - Windmill
Topic: 20’ Samson Model S
Replies: 153
Views: 42329

Re: 20’ Samson Model S

Hope everything coming along well on your big project. Here is a pic of the lettering on my tail bone. Tailbone with casting is
20200123_122729.jpg
21' long tall side of vane sheet is 8'5". The lettering would be located near the end of the tail on top of the angle.
by JLM
Thu Jan 23, 2020 12:26 pm
Forum: General Discussion
Topic: Drilling a Well
Replies: 22
Views: 7398

Re: Drilling a Well

Finally got those pictures scanned and downloaded. To my knowledge these photos came out of the Krueger family estate. Their Family owned SAMSCO san antonio machine and supply.The horse power could be used to power a drilling rig or pump water with as shown.