If as Peter says that an aermotor wheel will bolt right on then the radius of 19 and 37 are close enough for windmill tolerances.
Ron Stauffer
Montrose. CO
Search found 431 matches
- Thu Jan 11, 2024 5:58 pm
- Forum: Projects - Windmill
- Topic: new in Canada
- Replies: 117
- Views: 7769
- Thu Jan 04, 2024 12:30 am
- Forum: Sources for Components, Hardware, Materials, and Tooling
- Topic: Windmill Tower Punch
- Replies: 33
- Views: 3949
Re: Windmill Tower Punch
I dont often use it up on a tower. Usually setting a stub, there is an old head to remove so I am setting up the hoist anyway. Lay mill and tower down, chop the top, set the stub, put on new head and reset everything. That is the easiest and safest. I have used it twice in the air, once because it w...
- Wed Jan 03, 2024 12:43 am
- Forum: Name That Part (or Windmill or Tower)
- Topic: Diverter cup
- Replies: 6
- Views: 585
Re: Diverter cup
My first glance at the casting number.did not look like Aermotor because of the style type and font of the casting. I have 4 catalogs with the casting number of 233 on spout cup 20240102_220926.jpg A prefixes on aermotor parts were only for the 8 motors. Pump parts had a p and tower parts had a t. T...
- Wed Jan 03, 2024 12:26 am
- Forum: For Sale
- Topic: SOLD - 1899 Aermotor for parts
- Replies: 13
- Views: 1097
Re: 1899 Aermotor for parts - SOLD
The differentiation between the 98 and 99 tailbones are outlined in the narrative under this pic. Because the 99 is pull in mill, it has 2 additional attachments on the bones top strut next to the motor that the 98 doesn't have 20240102_120907.jpg Paul's next to last pic and two 8'and one 10' 99 bon...
- Sat Dec 23, 2023 8:04 pm
- Forum: For Sale
- Topic: SOLD - 1899 Aermotor for parts
- Replies: 13
- Views: 1097
Re: 1899 Aermotor for parts - SOLD
It is an 1899. Unmistakable 402 mainframe and part 441. Bone is 1899 but has been repaired with pipe. Aermotor pipe bone frames never had a pipe coupler in them...
Ron Stauffer
Montrose CO
Ron Stauffer
Montrose CO
- Fri Dec 15, 2023 10:45 am
- Forum: Projects - Windmill
- Topic: Disassembly and rehoming
- Replies: 6
- Views: 643
Re: Disassembly and rehoming
Is that a fiberglass helmet? Yes it is fiberglass. The entire head is 802 model through and through. Even the tower is 802 - universal steps, oversize sae hex hardware and 1.5" platform. Refer to Macdabs post in July. Removal would be complicated somewhat by the non existence of a brake band. ...
- Sat Dec 09, 2023 1:15 pm
- Forum: Sources for Components, Hardware, Materials, and Tooling
- Topic: Windmill Tower Punch
- Replies: 33
- Views: 3949
Re: Windmill Tower Punch
Cost is about $150. 20231128_163433.jpg We have made towers. When handling 20 foot pieces of steel, we drill all the tower holes. But we make patterns to speed up the process so that way we are only doing layout once. Once we have a pattern, we clamp it to a new piece to drill the holes. Drill press...
- Sat Dec 09, 2023 12:55 pm
- Forum: Sources for Components, Hardware, Materials, and Tooling
- Topic: Windmill Tower Punch
- Replies: 33
- Views: 3949
Re: Windmill Tower Punch
There is a factor that comes into consideration that was not addressed. Back in the day, there was corner tower angle that was up to 3 by 1/8 inch size but not anymore. The largest 1/8 inch angle is now 2 inch. Of course, there is not 2 1/4 inch angle that aermotor used for 6 and 8 foot mills. This ...
- Wed Nov 15, 2023 7:33 pm
- Forum: General Discussion
- Topic: Pump Fans
- Replies: 9
- Views: 428
Re: Pump Fans
Native Americans were far more advanced than us invaders . As Cochise said to Geronimo "we should have built a wall" Chaco is part of the National Park System with an official label of Chaco Culture National Historic Park and also a UNESCO World Heritage Site' Sixteen great houses have be...
- Wed Nov 15, 2023 2:19 am
- Forum: Projects - Windmill
- Topic: B602
- Replies: 22
- Views: 1474
Re: B602
Late in the post but here goes: Earliest 602 case with flat bottom and bottom drain plug (couldnt pick it up in a pic to be sure tho). The mast pipe was 661 with the flat heavy washer turntable. The cupped turntable pipe was 661 1/2. Aermotor never sold either turntable as a separate part but after ...