Friction Washers for 702 mill

......when you need to get in the weeds.
CTXmiller
Posts: 933
Joined: Sat Dec 15, 2018 12:01 pm
Location: Waco, TX

Re: Friction Washers for 702 mill

Post by CTXmiller »

#723 special hub
Wayne
Posts: 2115
Joined: Mon Dec 17, 2018 10:03 am
Location: Corsicana Tx.

Re: Friction Washers for 702 mill

Post by Wayne »

Thanks Windy. I was pretty sure I was seeing V spokes not screw in.
User avatar
windybob
Posts: 3508
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Friction Washers for 702 mill

Post by windybob »

Now I'm curious what the number on the case is. Can't see the front. I've heard of those special hub / shaft combinations.
Call Dan Benjamin for parts. P M me for the phone number.
Windy Bill
Posts: 17
Joined: Fri Aug 06, 2021 11:36 pm
Location: Richmond, Texas

Re: Friction Washers for 702 mill

Post by Windy Bill »

The hub is a 602. The case has A-702 embossed on it.
The statement about the upper case hole is badly worn? Not sure what you’re referring to?
I am setting it up to pump and circulate water to a round tank.
I cleaned it out with kerosene and not planning on rebuild. Replaced tail pivot rod and patched bullet hole in bonnet. Put it all together today, cleaned off the excess grease on mast. This was a running mill I picked up in western Kansas. I set the base of tower last week with legs in 4’ holes and 4 bags of concrete per hole. Had hell getting squared up but feel confident all is good. Saturday I have a water well guy coming to lift the top part of tower and fan onto base ..does anyone have the pump rod guides for the towe?
User avatar
windybob
Posts: 3508
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Friction Washers for 702 mill

Post by windybob »

Thanks for the update! Be very careful setting it up.

I know you said the hub was 602, does it by chance have ' A723 ' on it?

You can make pumprod guides out of 1/4 inch rod that pivots or lay a 2/4 with a notch cut out of it across the girts and clamp it.
Call Dan Benjamin for parts. P M me for the phone number.
mtblah
Posts: 1625
Joined: Thu Mar 26, 2020 12:09 pm
Location: new braunfels TX

Re: Friction Washers for 702 mill

Post by mtblah »

Windy Bob, is your house # 101, or, 204 , or 271796 ?
I on my way for that stake sandwich .

Mike Blahnik,
New Braunfels TX
User avatar
windybob
Posts: 3508
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Friction Washers for 702 mill

Post by windybob »

Mike PM on the way
Call Dan Benjamin for parts. P M me for the phone number.
Windy Bill
Posts: 17
Joined: Fri Aug 06, 2021 11:36 pm
Location: Richmond, Texas

Re: Friction Washers for 702 mill

Post by Windy Bill »

Has anyone used one of these for the pump on a mill? Isn’t supposed to have leathers?
You do not have the required permissions to view the files attached to this post.
User avatar
windybob
Posts: 3508
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Friction Washers for 702 mill

Post by windybob »

Yes that should have a leather. Looks like the bottom screws off to replace it.
Call Dan Benjamin for parts. P M me for the phone number.
User avatar
Bryon
Posts: 206
Joined: Sat Feb 16, 2019 4:35 pm
Location: Eastman, GA

Re: Friction Washers for 702 mill

Post by Bryon »

It also looks like a check valve (threads on the top). But yes, it should have a leather on it.
Post Reply