Sad news from Bulverde Texas

Share and discuss your windmill related projects.
DavidABarclay
Posts: 36
Joined: Tue Nov 03, 2020 6:56 am
Location: Bulverde Texas

Re: Sad news from Bulverde Texas

Post by DavidABarclay »

How in the name of Sam Hill do you get these off?
You do not have the required permissions to view the files attached to this post.
User avatar
Jim Corcoran
Posts: 304
Joined: Fri Dec 21, 2018 7:32 am
Location: Austin, Texas

Re: Sad news from Bulverde Texas

Post by Jim Corcoran »

If it was me, I would sandblast the threads to get them clean and then add some 3-in-1 oil or PB Blaster. You should go as easy as you can with the sandblaster to minimize the effect on the galvanized parts, possibly wrap some duct tape around the exposed area.

Jim
" You need to get at least 30 miles out of Austin before you're firmly back in Texas."
DavidABarclay
Posts: 36
Joined: Tue Nov 03, 2020 6:56 am
Location: Bulverde Texas

Re: Sad news from Bulverde Texas

Post by DavidABarclay »

Thanks Jim.
User avatar
windybob
Posts: 3870
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Sad news from Bulverde Texas

Post by windybob »

That's the first Dempster I can think of I've seen with galvanizing after bolted. Usually it's galvanized, then bolted. I think that's a better way, but I also think 4 legged towers are better than 3 . Lol (the age old argument)

Use a grinder. You are not going to re-use them most likely. Gee, what size wrench fits on that, anyway!
Call Dan Benjamin for parts. P M me for the phone number. IF YOU TALK TO HIM, AND HE HELPS YOU, THEN BUY FROM HIM. IT CREATES GOOD KARMA.
mtblah
Posts: 1999
Joined: Thu Mar 26, 2020 12:09 pm
Location: new braunfels TX

Re: Sad news from Bulverde Texas

Post by mtblah »

yup !
DavidABarclay
Posts: 36
Joined: Tue Nov 03, 2020 6:56 am
Location: Bulverde Texas

Re: Sad news from Bulverde Texas

Post by DavidABarclay »

Thanks Bob. I tried 3/8” and 12mm.
mtblah
Posts: 1999
Joined: Thu Mar 26, 2020 12:09 pm
Location: new braunfels TX

Re: Sad news from Bulverde Texas

Post by mtblah »

David, check your private messages.
Mike B
Wayne
Posts: 2290
Joined: Mon Dec 17, 2018 10:03 am
Location: Corsicana Tx.

Re: Sad news from Bulverde Texas

Post by Wayne »

I bought a long neck grinder that uses the 3 inch cut off wheels at Harbor Freight. I really like it for cutting off rivet head to remove blades. It is easier to control than the ones with the 90 degree wheels the wheel lays flat. It's about a foot long so you can get into hard to reach spots.
User avatar
Bryon
Posts: 206
Joined: Sat Feb 16, 2019 4:35 pm
Location: Eastman, GA

Re: Sad news from Bulverde Texas

Post by Bryon »

Air chisel, grinder. No need in saving those fasteners. Just get some new ones.
DavidABarclay
Posts: 36
Joined: Tue Nov 03, 2020 6:56 am
Location: Bulverde Texas

Re: Sad news from Bulverde Texas

Post by DavidABarclay »

Thanks Bryon & Wayne.
Post Reply