I'd like to buy/borrow the part in the red circle: "M7" on parts list--Actually, the pulley "92" would be nice too (Please PM me)
Burt
Aermotor M1 Grinder parts
Aermotor M1 Grinder parts
You do not have the required permissions to view the files attached to this post.
Last edited by hwy8 on Fri Jul 01, 2022 11:01 pm, edited 1 time in total.
-
Windcatcher530 Dan
- Posts: 1924
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: Aermotor M1 Grinder parts
Burt do you know the dimensions of the pulley and shaft size?
-
Windcatcher530 Dan
- Posts: 1924
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: Aermotor M1 Grinder parts
You do not have the required permissions to view the files attached to this post.
Re: Aermotor M1 Grinder parts
Dan, The shaft size is 1" diameter with about 4 1/2" exposed. That photo with the pulley in place came from "New Park Wind Engines" site. The one taken in the dark is mine. I also have an "N1" and I'm including a photo of that also which has a 1" shaft with a 4" hub and a pulley Diameter of 10". I don't know this, but it looks like the New Park grinder (M1) is being driven by the Power Mill and a belt is supposed to go on the spinning pulley: Maybe to operate the N1 grinder? The photo of the spinning pulley looks like the pulley diameter is larger, I suppose to increase the rpm's?
You do not have the required permissions to view the files attached to this post.
Re: Aermotor M1 Grinder parts
Another photo from "New Park Wind Engines" with a little different view. For the sake of scaling, that "yoke" looking part hanging on the bottom of the M1 is 10" wide.
You do not have the required permissions to view the files attached to this post.
-
Windcatcher530 Dan
- Posts: 1924
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: Aermotor M1 Grinder parts
I think this pulley went to a bigger grinder.
You do not have the required permissions to view the files attached to this post.
Re: Aermotor M1 Grinder parts
Dan, What size is your pulley? According to the text, the factory supplies a pulley that has a 15" diameter with a 4" face. Also, which catalog are those pages from and where can I buy a copy?
-
Windcatcher530 Dan
- Posts: 1924
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: Aermotor M1 Grinder parts
The pulley is 20in. X 4 if you zoom in on the picture of it you can see it scribed into the one spoke. Someone photo copied that info i have years ago and I don't remember who.
Re: Aermotor M1 Grinder parts
Thanks Dan, our conversation has been a lot of help to me. I have to say, after reading the material you have, I realize how little I know about these things! (nothing new there!)
-
Windcatcher530 Dan
- Posts: 1924
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: Aermotor M1 Grinder parts
Sorry the pulley won't work for you the grinder that came off of must have been bigger.when i bought the 14ft power mill that and other parts and pieces came with it along with a foot gear and slip clutch that ran the line shaft. He ground grain and sold it
