Page 1 of 2
Rivets for Sails
Posted: Mon Nov 04, 2019 10:55 am
by JBarker
In the old forum there was a really good thread on using or not using rivets on sails during restoration. I hope to start this again for future reference so please join the discussion and explain what you use --rivets or bolts...and why...pros and cons? Please explain your methods if you would be so kind. Thanks
Re: Rivets for Sails
Posted: Mon Nov 04, 2019 10:57 am
by JBarker
I will start the thread by saying I have been using stainless steel nuts and bolts w/lock washer on the Aermotor mills I have been working on. I hope to get more experience in using rivets in the near future if possible. Can anyone recommend a good place and the type to use? Thanks
Re: Rivets for Sails
Posted: Mon Nov 04, 2019 11:21 am
by PaulV
When I remove rivets, I go back with a bolt/screw, lockwasher and nut. Almost always galvanized. It doesn't matter to me that it's not 'original', and most can't tell/don't care when looking at a mill 20+ feet up. Whether they'll hold secure for as long as a rivet is yet to be determined, but they'll likely last longer than me, which is how I gauge repair quality nowadays
Re: Rivets for Sails
Posted: Mon Nov 04, 2019 12:00 pm
by billcobb
I use stainless steel industrial pop rivets that I get from a local auto parts store. Available in several lengths. You need a special version of the standard Harbor Fright installation tool to get them seated and compressed. It takes BOTH arms and a grunt to pull the pin heads through. They fit nicely into the rivet holes and don't need extra washers. Once you pull the pins through they have a wonderful habit/feature of showing up in any tires that may be driving by...
Re: Rivets for Sails
Posted: Mon Nov 04, 2019 1:18 pm
by JBarker
billcobb wrote: Mon Nov 04, 2019 12:00 pm
I use stainless steel industrial pop rivets that I get from a local auto parts store. Available in several lengths. You need a special version of the standard Harbor Fright installation tool to get them seated and compressed. It takes BOTH arms and a grunt to pull the pin heads through. They fit nicely into the rivet holes and don't need extra washers. Once you pull the pins through they have a wonderful habit/feature of showing up in any tires that may be driving by...
Bill, can you show us a pic of the special tool you use? Thanks
Re: Rivets for Sails
Posted: Mon Nov 04, 2019 4:44 pm
by windybob
Nuts and blots, as Jerry calls them. lol Rivets on occasion , if the customer demands original-type results.
This particular wheel has Stainless rims, and aluminum rivets. It will never move, so all is good. I would never use aluminum on a wheel if it moved. However, ALWAYS use locking hardware on a wheel.
waukomis 2.jpg
waukomis 1.jpg
Re: Rivets for Sails
Posted: Mon Nov 04, 2019 6:39 pm
by JBarker
windybob wrote: Mon Nov 04, 2019 4:44 pm
Nuts and blots, as Jerry calls them. lol Rivets on occasion , if the customer demands original-type results.
This particular wheel has Stainless rims, and aluminum rivets. It will never move, so all is good. I would never use aluminum on a wheel if it moved. However, ALWAYS use locking hardware on a wheel.
waukomis 2.jpg
waukomis 1.jpg
What is that monument of???
Re: Rivets for Sails
Posted: Tue Nov 05, 2019 7:30 am
by windybob
The town want to commemorate early settlers around 1895. They wanted a windmill, I suggested a period one. They agreed. It's a Dandy, from that year. Even says so on the tower leg. The statue is an early settler "finishing up the job" of putting the mill up.
Dandy 3....4-17.jpg
Dandy 2...4-17.jpg
Re: Rivets for Sails
Posted: Tue Nov 05, 2019 7:52 am
by JBarker
windybob wrote: Tue Nov 05, 2019 7:30 am
The town want to commemorate early settlers around 1895. They wanted a windmill, I suggested a period one. They agreed. It's a Dandy, from that year. Even says so on the tower leg. The statue is an early settler "finishing up the job" of putting the mill up.
Dandy 3....4-17.jpg
Dandy 2...4-17.jpg
Pretty cool pics
Re: Rivets for Sails
Posted: Tue Nov 05, 2019 8:12 am
by Wayne
Jerry, I got my Large Hand Riveter it's called from Jay-Cee Sales & Rivet.
www.rivetsinstock.com. Mine is lot num 80961-001. And as said I have to put small cheater bars on the handles to pop the 1/4 inch rivets.