Dandy

Generally speaking, this area is for general discussion about windmills, in most cases.
Post Reply
User avatar
Peter vk
Posts: 325
Joined: Sat Dec 15, 2018 11:30 am
Location: Chesterville Ontario Canada
Contact:
Contact Peter vk

Dandy

Post by Peter vk »

I did some work on somebodies windmill and found this way back in the bush, it was partially buried in the dirt. I was surprised when we got it out that it wasn't all rotted on the bottom. Got it home and fixed it up, it's going to be a wall hanger. It's off of at least a 12 footer maybe even a 14 footer, it's almost the same size as the one behind it which is a 14 footer. It says Dandy the Windmotor co Limited, Woodstock Ont.
Peter
You do not have the required permissions to view the files attached to this post.
Top
User avatar
windybob
Posts: 3806
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Dandy

Post by windybob »

:o
Call Dan Benjamin for parts. P M me for the phone number. IF YOU TALK TO HIM, AND HE HELPS YOU, THEN BUY FROM HIM. IT CREATES GOOD KARMA.
Top
CTXmiller
Posts: 1046
Joined: Sat Dec 15, 2018 12:01 pm
Location: Waco, TX

Re: Dandy

Post by CTXmiller »

Nice find
Top
Windcatcher530 Dan
Posts: 2126
Joined: Sun Mar 28, 2021 4:06 pm
Location: Alcove N.Y.i buy and restore

Re: Dandy

Post by Windcatcher530 Dan »

Peter are you familiar with that company?
Top
User avatar
Peter vk
Posts: 325
Joined: Sat Dec 15, 2018 11:30 am
Location: Chesterville Ontario Canada
Contact:
Contact Peter vk

Re: Dandy

Post by Peter vk »

Windcatcher530 Dan wrote: ↑Sat Dec 03, 2022 2:46 pm Peter are you familiar with that company?
No I don't know much about them. I think they sold the American made Challenge Dandy. That tail is the only thing I have found from them.
Top
Windcatcher530 Dan
Posts: 2126
Joined: Sun Mar 28, 2021 4:06 pm
Location: Alcove N.Y.i buy and restore

Re: Dandy

Post by Windcatcher530 Dan »

From what I found they started in the 1890s into the early 1900s. They also made two other mills the WINDPOWER and the WOODSTOCK both in pumping and power mills. Pretty cool!!!
Top
Old windy one
Posts: 25
Joined: Wed Jul 28, 2021 1:33 pm
Location: near the center peoples republic of Kalifornia.

Re: Dandy

Post by Old windy one »

What a great find, especially with the logo still legible on it!!
Top
mtblah
Posts: 1903
Joined: Thu Mar 26, 2020 12:09 pm
Location: new braunfels TX

Re: Dandy

Post by mtblah »

some people have all the luck ! nice find ......
Top
Windcatcher530 Dan
Posts: 2126
Joined: Sun Mar 28, 2021 4:06 pm
Location: Alcove N.Y.i buy and restore

Re: Dandy

Post by Windcatcher530 Dan »

The DANDY they sold was made by them I believe and had the replaceable Graphite bearings.
Top
User avatar
Peter vk
Posts: 325
Joined: Sat Dec 15, 2018 11:30 am
Location: Chesterville Ontario Canada
Contact:
Contact Peter vk

Re: Dandy

Post by Peter vk »

Windcatcher530 Dan wrote: ↑Sat Dec 03, 2022 8:28 pm The DANDY they sold was made by them I believe and had the replaceable Graphite bearings.
So where did you find that info?
Top
Post Reply

Return to “General Discussion - Windmill”