Windmill and tower markings - black paint / ink

Generally speaking, this area is for general discussion about windmills, in most cases.
User avatar
PaulV
Site Admin
Posts: 1121
Joined: Wed Dec 12, 2018 10:52 pm
Location: Collinsville, Oklahoma
Contact:

Re: Windmill and tower markings - black paint / ink

Post by PaulV »

Ron Stauffer wrote: Thu Jul 18, 2024 2:33 pm Was it standing and complete when you got it?

Was it the original installation?

Were there any other shipping addresses on the tower?Or tail vane?

Corner angle of 2 and a 1/2. Or 2 and 3 /8.?
(2) 20' sections. Original installation and complete. Blown over in recent storm. Ground anchors rusted thru. We disassembled where it fell. 2-3/8" angle.

So far, I've only found "Fairland OK" in writing on a leg. Nothing on vane. I believe an open gear was original, replaced with A602.

Mill was over a 25' hand dug and lined well.
PaulV
Ron Stauffer
Posts: 504
Joined: Fri Dec 14, 2018 10:25 am
Location: Uncompahgre Plateau Montrose CO
Contact:

Re: Windmill and tower markings - black paint / ink

Post by Ron Stauffer »

I would go 99% likelihood of an original open gear.

OK guys, what is the incongruity?

First hint, the shipper was psychic and could see 50 years in the future.

I am going to make this one hard...

Ron
mtblah
Posts: 1951
Joined: Thu Mar 26, 2020 12:09 pm
Location: new braunfels TX

Re: Windmill and tower markings - black paint / ink

Post by mtblah »

Ron , thank you for making me smile 😆
Never would have thought to add asbestos to make it fire proof
Ron Stauffer
Posts: 504
Joined: Fri Dec 14, 2018 10:25 am
Location: Uncompahgre Plateau Montrose CO
Contact:

Re: Windmill and tower markings - black paint / ink

Post by Ron Stauffer »

Mike
AI was really Aermotor Intelligence until the techies hijacked it. Paul gave his hijack blessing to me on this post

Ron
Windcatcher530 Dan
Posts: 2173
Joined: Sun Mar 28, 2021 4:06 pm
Location: Alcove N.Y.i buy and restore

Re: Windmill and tower markings - black paint / ink

Post by Windcatcher530 Dan »

I believe that the first trussed tripod tower was in 1904 !! Pretty sure, I think !!!
Ron Stauffer
Posts: 504
Joined: Fri Dec 14, 2018 10:25 am
Location: Uncompahgre Plateau Montrose CO
Contact:

Re: Windmill and tower markings - black paint / ink

Post by Ron Stauffer »

Irrelevance to the incongruity.

In the words of a female I once knew,
my game, I make the rules. No hint
Ron Stauffer
Posts: 504
Joined: Fri Dec 14, 2018 10:25 am
Location: Uncompahgre Plateau Montrose CO
Contact:

Re: Windmill and tower markings - black paint / ink

Post by Ron Stauffer »

Paul
I would like to see a pic of the vane to know which mill it was original to.

No rush, as I need lots of time to think of obscure hints.
for the incongruity.

Ron
Reddirtwind
Posts: 44
Joined: Wed Apr 26, 2023 9:33 pm
Location: Amarillo

Re: Windmill and tower markings - black paint / ink

Post by Reddirtwind »

State abbreviation for OK?? (Two letter. Most probably used Okla, before the 2-letter was introduced.)
Ron Stauffer
Posts: 504
Joined: Fri Dec 14, 2018 10:25 am
Location: Uncompahgre Plateau Montrose CO
Contact:

Re: Windmill and tower markings - black paint / ink

Post by Ron Stauffer »

Dang, I thought I could keep it going.

Yes the incongruity is Ok. I have seen lots of Okla terr or Okla but not Ok. My other clues were going to be that the shipper either had the flu or he and his wife were expecting any time because of the incompletion
Ron Stauffer
Posts: 504
Joined: Fri Dec 14, 2018 10:25 am
Location: Uncompahgre Plateau Montrose CO
Contact:

Re: Windmill and tower markings - black paint / ink

Post by Ron Stauffer »

2 letters State designations didn't start until 1963 and have never seen them on windmill tails.
Post Reply