Tower lightning protection?

Generally speaking, this area is for general discussion about windmills, in most cases.
bobceng
Posts: 23
Joined: Tue Aug 25, 2020 6:28 pm
Location: Northport, Michigan

Tower lightning protection?

Post by bobceng »

Hello; will be raising my steel tower next year. What is the general thinking about lightning protection? Most of these towers have been up for 100 years without incident, but still...
User avatar
windybob
Posts: 4061
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Tower lightning protection?

Post by windybob »

I would not lose any sleep over it. It's very rare, plus they are grounded good.
Call Dan Benjamin for parts. P M me for the phone number. IF YOU TALK TO HIM, AND HE HELPS YOU, THEN BUY FROM HIM. IT CREATES GOOD KARMA.
bobceng
Posts: 23
Joined: Tue Aug 25, 2020 6:28 pm
Location: Northport, Michigan

Re: Tower lightning protection?

Post by bobceng »

Thanks; windy bob. Our soil is very sandy here in northern Michigan, and I am wondering at its conductivity. Anyway, I will take your advice and not lose too much sleep; I just won't be sleeping under the tower during a thunderstorm!
User avatar
windybob
Posts: 4061
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Tower lightning protection?

Post by windybob »

PLant a tall tree next to it. That will fix it. LOL
Call Dan Benjamin for parts. P M me for the phone number. IF YOU TALK TO HIM, AND HE HELPS YOU, THEN BUY FROM HIM. IT CREATES GOOD KARMA.
bobceng
Posts: 23
Joined: Tue Aug 25, 2020 6:28 pm
Location: Northport, Michigan

Re: Tower lightning protection?

Post by bobceng »

Either way, I lose...I will have a nice big tree next to it, and then wonder why there's not enough wind to turn my mill!! (I think this is where the crying emojis are supposed to go)
User avatar
windybob
Posts: 4061
Joined: Mon Jan 14, 2019 5:59 pm
Location: Ames Oklahoma

Re: Tower lightning protection?

Post by windybob »

If your mill ever gets hit by lightening, send me proof, and I will furnish replacement parts for shipping only. And I'm not going to lose any sleep over that either...
Call Dan Benjamin for parts. P M me for the phone number. IF YOU TALK TO HIM, AND HE HELPS YOU, THEN BUY FROM HIM. IT CREATES GOOD KARMA.
bobceng
Posts: 23
Joined: Tue Aug 25, 2020 6:28 pm
Location: Northport, Michigan

Re: Tower lightning protection?

Post by bobceng »

OK...good enough for me. Seriously, I like the idea of bolting 5' angle iron leg extensions with "T" ends to the (3) tower legs. Ground water shows up at 6' to 8' depth, so conductivity should be good. If I want to go the "belt AND suspenders" route, driving an 8 foot grounding rod bonded to each leg would be cheap insurance.
User avatar
PaulV
Site Admin
Posts: 1191
Joined: Wed Dec 12, 2018 10:52 pm
Location: Collinsville, Oklahoma
Contact:

Re: Tower lightning protection?

Post by PaulV »

You won't need ground rods. The tower is going to be well grounded once you anchor it.

Welcome to the forum!
PaulV
Smax
Posts: 462
Joined: Thu Jan 03, 2019 12:06 pm
Location: Ardmore,oklahoma
Contact:

Re: Tower lightning protection?

Post by Smax »

FB_IMG_1596134996329.jpg
I this a girt that was struck by lightening . The girts,braces and tower leg all had the dendritic pattern as the lightening went to the ground. Looked like someone had taken a plasma torch to it . I have seen trees with that pattern but this was the first windmill. I saved a couple of the pieces
You do not have the required permissions to view the files attached to this post.
bobceng
Posts: 23
Joined: Tue Aug 25, 2020 6:28 pm
Location: Northport, Michigan

Re: Tower lightning protection?

Post by bobceng »

What were the footings for the tower? Concrete pad, or steel leg extensions directly into the earth?

This is a similar pattern I saw on a dead ash tree that was struck a couple of years back. I was standing about 100 feet from the tree when it was struck...flash-bang!!!! Splinters of bark and wood blew in a fan shape debris field for a couple of hundred feet.

You don't play around with lightning.
Post Reply